Buchsen, Schalter, Potis, etc.

438 Produkte

EMERSON CUSTOM – 5-Way Stratocaster Blender Prewired Kit (250K Ohm Pots & 0.047uf Capacitor)

Emerson Custom 5-Way Stratocaster Blender Prewired Kit (250K Ohm Pots & 0.047uf Capacitor) Prewired Kit - Handwired in the USA - Features Emerson PRO CTS Potentiometers Our Blender wiring has 1 volume, 1 master tone, and a Blender pot. In the neck position you can blend the bridge pickup in as much as you want. In the bridge position you can blend the neck pickup in as much as you want. In positions 2 and 4 you can have all three pickups on at once. The nicest part about it is the fact of it being so user friendly. Everything else seems to be hard to use on the fly. 1: Emerson Pro CTS Volume Pot (Master Volume) [3/8" Split Shaft] 1: Emerson Pro CTS Tone Pot (Master Tone) [3/8" Split Shaft] 1: Emerson Pro CTS 250K Blender Pot [3/8" Split Shaft] 1: 0.047uf Emerson Paper in Oil Capacitor *(0.022uf are used with 500K-Ohm Pots Option)* 1: Volume Mod (Treble Bleed; Retains Clarity when rolling back volume knob) 1: Prewired Jack 1: Wiring Diagram Control Layout: - Master Volume - Master Tone - Blender Pot Switch & Blender Pot Function: Blender Pot on 10: Position 1: Bridge Position 2: Bridge & Middle Position 3: Middle Position 4: Middle & Neck Position 5: Neck Blender Pot on 1: Position 1: Bridge w/ Neck Pickup Blended in Position 2: Bridge & Middle w/ Neck Pickup Blended in Position 3: Middle Position 4: Middle & Neck w/ Bridge pickup Blended in Position 5: Neck w/ Bridge Pickup Blended in Our Emerson Pro split shaft pots are made to fit USA Spec 24 spline push-on knobs. Some USA & Import Guitars will need new USA Spec Knobs as even some US makers use import spec parts which will not work with our pots. We recommend that you don't rush the knob install process. If your knob is too tight and is not going on ,slightly crimp together the top of the potentiometers shaft ever so slightly so that when you go to push on the knob you don't damage the pot shaft by exerting too much downward pressure. If you have any questions regarding install please let us know. Thank you.

98,00 €*

verfügbar

EMG – 1 or 2 Pickup Wiring Kit

- Kit mit allem, was man für den Einbau für 1 oder 2 aktive EMG Solderless Tonabnehmer braucht enthält Potis mit Riffelachse in Standardlänge nur für aktive Tonabnehmer geeignet - 2 Volume Potis - 2 Ton Potis - 1 Pickup Buss - 1 Power Buss - 1 12B Ausgangsbuchse mit Batterie Clip - 1 Ausgangskabel - 4 Interconnect Kabel - 2 Pickup Kabel

42,00 €*

verfügbar

EMERSON CUSTOM – 4-Way Lever Switch made by Oak Grigsby

- 4-Wege Austauschschalter für T-Style- und andere Gitarren - Originalschalter auf vielen USA-Gitarren seit den 90ern - hergestellt von Oak Grigsby - inkl. Befestigungsschrauben - made in USA

29,90 €*

verfügbar

EMG – 3 Position Toggle Switch BK

EMG 3 Pos Toggle Switch BK 3-Wege Schalter - original EMG solderless Low-Profile 3-Wege-Schalter - passend für die meisten Standard 2 x Humbucker Gitarren - Kappe: Schwarz

27,99 €*

verfügbar

EMERSON CUSTOM – PRO CTS - 1 Meg Short (3/8") Solid Shaft Potentiometer

Die Emerson Pro CTS-Potis von Emerson Custom sind die erste Wahl für den anspruchsvollen Gitarristen, der ein Optimum an Leistung und tonaler Ansprache von einem Gitarrenpotentiometer erwartet. Diese speziell entwickelten Emerson Pro CTS haben eine langlebigere Messingwelle und -buchse. Sie haben auch eine engere Widerstandstoleranz von ±8% im Vergleich zu den CTS-Produkten der meisten anderen Anbieter. Jedes einzelne Emerson Pro CTS Potentiometer wird von Hand getestet, um sicherzustellen, dass es die von uns angegebenen Toleranzen einhält oder übertrifft. Wir sind sehr stolz darauf, einige der besten und beständigsten Potentiometer auf dem heutigen Markt anbieten zu können. Emerson Pro CTS Potentiometer haben einen speziellen Audio-Konus, der speziell von Emerson Custom entwickelt wurde, um eine sehr weiche und genaue Reaktion zu gewährleisten, wenn Sie die Regler auf und ab bewegen. Diese Potentiometer bieten einen viel reaktionsfreudigeren Kegel als die Standard CTS-Potentiometer, die Sie in der Economy-Ausführung erhalten. Drehen Sie Ihre Gitarre auf 10 und die Lautstärke schwillt bis zum Anschlag an - kein abruptes Abflachen, das Ihren Spielstil ersticken könnte. Klarheit und Präzision zeichnen diese Serie von Premium-Potentiometern von Emerson Custom aus. Jedes Emerson Pro CTS-Potentiometer enthält eine flache Unterlegscheibe, eine Sicherungsscheibe und zwei Sechskantmuttern zur individuellen Höhenanpassung auf einem Schlagbrett, einer Reglerplatte oder direkt auf der Gitarrenoberseite im Inneren der Regleraussparung. Artikeldetails - Low Torque (Easy turning - for quicker/easier Volume & Tone swells. - 3/8" Solid Shaft for use with (1/4”) US Spec set-screw knobs. - Typically used on Fender Style Guitars with Single Coil Pickups (i.e.: Jazzmasters, Jaguars, etc) - Shaft Style: ROUND SOLID SHAFT - Shaft Diameter: 0.250” (6.35MM) - Shaft Height: 3/8” (9.52MM) - Thread: 3/8” X 32 - Thread Height: 3/8” (9.52MM) - Required Mounting Hole: 3/8” (9.52MM)

17,90 €*

verfügbar

EMERSON CUSTOM – PRO CTS - 250K Short (3/8") Solid Shaft Potentiometer

- Low Torque (Easy turning - for quicker/easier Volume & Tone swells. - 3/8" Solid Shaft for use with (1/4”) US Spec set-screw knobs. - Typically used on Tele Style Guitars with Single Coil Pickups Emerson Pro CTS pots from Emerson Custom were designed to be the premium choice for the discerning guitarist looking for the optimum performance and tonal response from a guitar potentiometer. These specially designed Emerson Pro CTS feature a longer-life brass shaft and bushing. They also feature a tighter ±8% resistance tolerance compared to CTS products offered by most other suppliers. Each and every Emerson Pro CTS pot is hand tested to ensure that they meet or exceed our stated tolerances. We take great pride in offering some of the best, most consistent potentiometers on the market today. Emerson Pro CTS pots have a proprietary custom audio taper that was specially designed by Emerson Custom to give you a very smooth and accurate response when you roll up and down on the controls. These pots will give you a much more responsive taper than what you'll get with economy or even standard issue CTS pots. Crank your guitar up to 10 and the volume swells all the way—no abrupt flattening to choke your playing style. Clarity and Precision define this Series of Premium Potentiometers by Emerson Custom. Each Emerson Pro CTS pot includes a flat washer, lock washer, and two hex mounting nuts for custom height adjustment on a pickguard, control plate, or directly on to the guitars top from inside the control cavity. - Shaft Style: ROUND SOLID SHAFT - Shaft Diameter: 0.250” (6.35MM) - Shaft Height: 3/8” (9.52MM) - Thread: 3/8” X 32 - Thread Height: 3/8” (9.52MM) - Required Mounting Hole: 3/8” (9.52MM)

17,90 €*

verfügbar

EMERSON CUSTOM – Mono Switchcraft J11 Input Jack - Long Thread (3/8") - Mono Buchse

- Aáccepts standard 1/4" plugs- requires 3/8"- diameter mounting hole- 3/8 x 32 threaded portion is 3/8" long- option for 3/8 x 32 threaded portion 3/8" long. Perfect for use in SG's hollowbodies, etc.- mounting nut and flat washer included.- made in the USA

9,90 €*

verfügbar

CTS – 500K Poti, lin., langer Schaft .750"", 3/8"" Durchm., für gewölbte Decken

PotentiometerValue:Typically 250K pots are used for single coil pickups and 500K pots for humbucker pickups. The bigger the resistence value, the brighter the sound will be/ less highs will bleed off. 1MEG can be used to make humbuckers sound brighter.Taper:The taper of a pot refers to the way its resistance changes as the shaft is rotated. A linear taper pot will work in a linear way related to shaft rotation. As the human ear is not linear in response to increasing volume an audio or logarithmic pot will work best for volume applications.Shaft:A split, knurled shaft will hold most knobs. Sometimes the knob is mounted using a set screw. You should order a solid shaft pot, or align the set screw with the split for correct mounting.Bushing:The standard bushing diameter is 3/8" or 9,5mm, used in most made in USA guitars. Another industry standard is M8, as used by guitar builders outside of the USA. When space is limited mini pots are used with a shaft diameter of 7mm.The standard bushing length is .375" for inch type pots and 10mm for metric type pots. Using two nuts it is very easy to set the correct bushing length for knob placement. Specially for pickguard (ST, PB) or control plate mount (TE, JB) the .250" short bushing will fit perfectly using only one nut.For use with a thick or carved top (LP USA) you should order a bushing length of .750".CTS is (and has been since the 50's) a factory standard for most USA brands like Fender and Gibson. Alpha is a good alternative, nowadays used as a factory standard by Ibanez, Epiphone and Squier.

8,50 €*

verfügbar

CTS – 250K Poti, log., kurzer Schaft .250"", 3/8"" Durchm., FE-style back, Pickguardmontage

Typischerweise werden 250K-Potis für Single-Coil-Tonabnehmer und 500K-Potis für Humbucker-Tonabnehmer verwendet. Je größer der Widerstandswert ist, desto heller wird der Klang / weniger Höhen werden ausgeblasen. 1MEG kann verwendet werden, um Humbucker heller klingen zu lassen. Die Verjüngung eines Potis bezieht sich auf die Art und Weise, wie sich der Widerstand ändert, wenn die Welle gedreht wird. Ein Potentiometer mit linearer Verjüngung arbeitet linear in Bezug auf die Drehung der Welle. Da das menschliche Ohr nicht linear auf steigende Lautstärke reagiert, eignet sich ein Audio- oder logarithmisches Poti am besten für Lautstärkeanwendungen. Die meisten Drehknöpfe werden mit einer geteilten, gerändelten Welle befestigt. Manchmal wird der Drehknopf mit einer Stellschraube befestigt. Sie sollten ein Potentiometer mit festem Schaft bestellen oder die Stellschraube zur korrekten Montage auf den Schlitz ausrichten. Der Standard-Buchsen-Durchmesser ist 3/8" oder 9,5mm, der in den meisten "Made in USA"-Gitarren verwendet wird. Ein anderer Industriestandard ist M8, wie er von Gitarrenbauern außerhalb der USA verwendet wird. Wenn der Platz begrenzt ist, werden Mini-Potis mit einem Schaftdurchmesser von 7mm verwendet. Die Standardbuchsenlänge beträgt .375" für zöllige Potis und 10mm für metrische Potis. Mit Hilfe von zwei Muttern ist es sehr einfach, die richtige Buchsenlänge für die Drehknopfplatzierung einzustellen. Speziell für Pickguard- (ST, PB) oder Control Plate-Montage (TE, JB) passt die .250" kurze Buchse perfekt mit nur einer Mutter. CTS ist (und war seit den 50er Jahren) ein Werksstandard für die meisten USA-Marken wie Fender und Gibson. Alpha ist eine gute Alternative, die heute als Werksstandard von Ibanez, Epiphone und Squier verwendet wird.

6,90 €*

verfügbar

CTS – 250K Poti, linear, kurzer Schaft .250"", 3/8"" Durchm., FE-style back, Pickguardmontage

CTS 250K Poti, linear, kurzer Schaft .250"", 3/8"" Durchm., FE-style back, Pickguardmontage Potentiometer Value: Typically 250K pots are used for single coil pickups and 500K pots for humbucker pickups. The bigger the resistence value, the brighter the sound will be/ less highs will bleed off. 1MEG can be used to make humbuckers sound brighter. Taper: The taper of a pot refers to the way its resistance changes as the shaft is rotated. A linear taper pot will work in a linear way related to shaft rotation. As the human ear is not linear in response to increasing volume an audio or logarithmic pot will work best for volume applications. Shaft: A split, knurled shaft will hold most knobs. Sometimes the knob is mounted using a set screw. You should order a solid shaft pot, or align the set screw with the split for correct mounting. Bushing: The standard bushing diameter is 3/8" or 9,5mm, used in most made in USA guitars. Another industry standard is M8, as used by guitar builders outside of the USA. When space is limited mini pots are used with a shaft diameter of 7mm. The standard bushing length is .375" for inch type pots and 10mm for metric type pots. Using two nuts it is very easy to set the correct bushing length for knob placement. Specially for pickguard (ST, PB) or control plate mount (TE, JB) the .250" short bushing will fit perfectly using only one nut. For use with a thick or carved top (LP USA) you should order a bushing length of .750". CTS is (and has been since the 50's) a factory standard for most USA brands like Fender and Gibson. Alpha is a good alternative, nowadays used as a factory standard by Ibanez, Epiphone and Squier.

6,90 €*

verfügbar

GÖLDO MUSIC – US500 Poti im CTS-Style 500K log

Mit verzinntem Gehäuse für 1A-Lötbarkeit und Riffelachse. Messinggewinde 9 x 10mmØ, Gehäuse 24mmØ.

4,90 €*

verfügbar

ALPHA – 1MEG Poti, Potentiometer log., Solid Shaft, kurz .250"", 3/8"" Durchm., für Pickguard

Alpha 1MEG Poti, Potentiometer log., Solid Shaft, kurz .250"", 3/8"" Durchm., für Pickguard Potentiometer Value: Typically 250K pots are used for single coil pickups and 500K pots for humbucker pickups. The bigger the resistence value, the brighter the sound will be/ less highs will bleed off. 1MEG can be used to make humbuckers sound brighter. Taper: The taper of a pot refers to the way its resistance changes as the shaft is rotated. A linear taper pot will work in a linear way related to shaft rotation. As the human ear is not linear in response to increasing volume an audio or logarithmic pot will work best for volume applications. Shaft: A split, knurled shaft will hold most knobs. Sometimes the knob is mounted using a set screw. You should order a solid shaft pot, or align the set screw with the split for correct mounting. Bushing: The standard bushing diameter is 3/8" or 9,5mm, used in most made in USA guitars. Another industry standard is M8, as used by guitar builders outside of the USA. When space is limited mini pots are used with a shaft diameter of 7mm. The standard bushing length is .375" for inch type pots and 10mm for metric type pots. Using two nuts it is very easy to set the correct bushing length for knob placement. Specially for pickguard (ST, PB) or control plate mount (TE, JB) the .250" short bushing will fit perfectly using only one nut. For use with a thick or carved top (LP USA) you should order a bushing length of .750". CTS is (and has been since the 50's) a factory standard for most USA brands like Fender and Gibson. Alpha is a good alternative, nowadays used as a factory standard by Ibanez, Epiphone and Squier.

2,50 €*

verfügbar

ALPHA – 500K Poti, Potentiometer linear, Solid Shaft, kurz .250"", 3/8"" Durchm., für Pickguard

Alpha 500K Poti, Potentiometer linear, Solid Shaft, kurz .250"", 3/8"" Durchm., für Pickguard Potentiometer Value: Typically 250K pots are used for single coil pickups and 500K pots for humbucker pickups. The bigger the resistence value, the brighter the sound will be/ less highs will bleed off. 1MEG can be used to make humbuckers sound brighter. Taper: The taper of a pot refers to the way its resistance changes as the shaft is rotated. A linear taper pot will work in a linear way related to shaft rotation. As the human ear is not linear in response to increasing volume an audio or logarithmic pot will work best for volume applications. Shaft: A split, knurled shaft will hold most knobs. Sometimes the knob is mounted using a set screw. You should order a solid shaft pot, or align the set screw with the split for correct mounting. Bushing: The standard bushing diameter is 3/8" or 9,5mm, used in most made in USA guitars. Another industry standard is M8, as used by guitar builders outside of the USA. When space is limited mini pots are used with a shaft diameter of 7mm. The standard bushing length is .375" for inch type pots and 10mm for metric type pots. Using two nuts it is very easy to set the correct bushing length for knob placement. Specially for pickguard (ST, PB) or control plate mount (TE, JB) the .250" short bushing will fit perfectly using only one nut. For use with a thick or carved top (LP USA) you should order a bushing length of .750". CTS is (and has been since the 50's) a factory standard for most USA brands like Fender and Gibson. Alpha is a good alternative, nowadays used as a factory standard by Ibanez, Epiphone and Squier.

2,50 €*

verfügbar

GÖLDO MUSIC – Kondensator für Tonregler / 10nF

Bewährter 10nF-Kondensator für die Klangregelung von Gitarren und Bässen. Wir empfehlen 10, 15 oder 22 nF für Gitarren- und 22, 33 oder 47 nF für Bass-Anwendung. Je höher der Wert, umso dumpfer bei herunter gedrehtem Tonregler der Sound. Für lautere Pickups wie z.B. Humbucker empfehlen sich kleinere Werte als für Singlecoils. Artikeldetails - Kondensator für Tonpoti - 10 nF